Signal Treatment and Analysis
Sharing Meaningful and Relevant Assay Data
Make the most out of HTRF^{®} assay data
Learn how to ensure the maximum significance of result interpretation by addressing the following points:
 How to perform a ratiometric data analysis step that will clear results from background or compound interference, medium effects or pipetting variations
 How to perform 4PL 1/y^2 curve fitting for cytokine assays in order to accurately measure samples across wide ranges of concentrations.
Ratiometric data analysis: a straightforward way to eliminate compound interference or normalize data between assays
What it is and what it adds to data analysis
The ratiometric analysis of data is a unique feature of HTRF assays which result into significant improvement of data quality. It relies on measuring fluorescence at 2 different wavelengths from the donor and the acceptor (See table 1) and processing the resulting signals into a single value that compensates for the following risks:
 Welltowell variations that may arise from pipetting error or imprecision.
 Compounds and/or media components added in the plate that may change the photophysical properties in a given well, and the degree to which this occurs can vary from sample to sample.
Correction by the ratiometric analyses will provide more robust datasets between replicates (intraassay) or between assay runs (interassay).
XL665  d2  Green dye  

Eu3+ cryptate  620 nm 665 nm 
620 nm 665 nm 

Tb3+ cryptate  620 nm 665 nm 
620 nm 665 nm 
620 nm 520 nm 
Table 1: recommended wavelengths to measure for the ratiometric reduction of data
How it works: the ratiometric analysis in action
Data analysis: case of standard curves in a competitive assay
Ratio and delta ratio
Five standards were plated and incubated with HTRF reagents. Their emissions at 665 nm (Acceptor) and 620 nm (Donor) were measured after incubation (Table 2.a).
The ratio must be calculated for each well individually. The mean and standard deviation can then be worked out from replicates. A 10^4 multiplying factor is introduced for easier data processing (Table 2.b)
The delta ratio (ΔR) reflecting the “specific signal” is obtained by simply subtracting the background from the signal of each positive point (Table 2.c).
Channel A 665 nm 
Channel B 620 nm 


Background  2040  40765 
Std 0  45999  41442 
Std 1  40615  41000 
Std 2  29212  41732 
Std 3  15249  40124 
Std 4  6258  39124 
a. Standard emissions at 665 nm and 620 nm
Ratio 

500 
11100 
9906 
7000 
3800 
1600 
b. HTRF ratio
Delta ratio (ΔR) 

10599 
9406 
6499 
3300 
1099 
c. Delta ratio
Assay window
The window is obtained by dividing the maximum signal ratio value by the minimum signal ratio value (Table 3).
Ratio  

Background  500 
Std 0  11100 (Max) 
Std 1  9906 
Std 2  7000 
Std 3  3800 
Std 4  1600 (Min) 
Assay window 

7 
Data normalization for comparing two assays
Delta F for interassay comparisons
Delta F is used for the comparison of daytoday runs of the same assay or assays run by different users. It reflects the signal to background of the assay. The negative control plays the role of an internal assay control.
The following table only exemplifies the normalization of one of the assays (#1), but both assays compared should be treated this way.
Assay #1  Channel A 665 nm  Channel B 620 nm  Ratio 

Background  2140  42765  500 
std 0  75241  43242  17400 
Std 1  69319  45100  15370 
Std 2  49115  44732  10980 
Std 3  25098  43124  5820 
Std 4  9991  43924  2275 
ΔF 

3377% 
2971% 
2094% 
1063% 
355% 
Delta F / Delta F max enables the comparison of two experiments
This calculation is used for normalizing the signal in competitive assays. This is done for both assays.
Assay #1  ΔF 

Background  
std 0  3377% 
Std 1  2971% 
Std 2  2094% 
Std 3  1063% 
Std 4  355% 
Assay #1  ΔF/ΔF max 

Background  
std 0  100% 
Std 1  88% 
Std 2  62%</td > 
Std 3  31% 
Std 4  10% 
Determination of the negative control
Sandwich and direct binding assays
Sandwich assays’ negative control should involve both antibodycoupled HTRF reagents to test for their respective specificity and ensure they do not generate FRET signal in the absence of their target proteins.
When performing a direct binding assay (immunocompetitive assays), we recommend you perform a cryptate blank negative control with all assay components but the acceptor conjugate.
4PL 1/y^{2} fitting for Cisbio cytokine assays
The 4 Parameter Logistic (4PL) curve is the most commonly recommended curve for fitting an ELISA standard curve (Fig. 1 for example).
4PL regression enables the accurate measurement of an unknown sample across a wider range of concentrations than linear analysis, making it ideally suited to the analysis of biological systems like cytokine releases. This is especially true in the lowend concentrations of the standard curve, where data points would be “lost” in a linear regression.
No need for a degree in Statistics to use this equation and analyze data. Software programs like Prism or Excel allow you to run a 4PL analysis without getting into the math, and there are free online software able to run this analysis.
Even though linear regression is easy to use and can be run with a very low number of standard points, it is not considered the best fitting method for biological phenomena like cytokine release, especially in an immunoassay. The main drawback is that it is only applicable for samples that fall within the linear range of the assay, thus reducing analysis flexibility (dilutions …).
The 4PL equation includes 4 variable parameters related to the curve:
 Estimated response at concentration zero
 Estimated response at maximal signal
 Slope factor
 Midrange concentration (or “point of inflexion”)
To get the most out of your data, we add a 1/y^{2} weighting to the equation, thus making it a 4PL 1/y^{2} fitting. The 1/y^{2} correction basically considers the changes of variance occurring with an increase in signal and provides.
 A broader range of concentrations for analysis
 Accuracy in the low/high ends of the standard curve
How to run 4PL 1/y^{2} analysis
Graphpad Prism V7 of higher
If you are using GraphPad Prism 7: choose the “four parameters” equation available in the software. Among the 2 equations suggested, we recommend the use of “four parameters” equation, the other “4PL” equation is NOT SUITED for analyzing cytokine assays.
Graphpad Prism Version lower than 7
If you are using an older version than Graphpad Prism 7, we have detailed the stepbystep procedure to run the analysis in this video:
Since Graphpad Prism Version 6, the 4PL equation has been already built into the software, but if you have any doubts, you can download the following Prism file with the HTRF 4PL already built in (Zip file).
Free online software
If you do not have any version of Graphpad Prism, we have tested several free online software programs and we highly recommend MyAssays.com. This free online analysis software will give you access to easy data analysis, analysis customization and export capabilities.